How to replace the fan in the laptop hp:

The fan in the laptop is an important detail on which the stable operation and cooling of the device depends. Over time, it may be necessary to replace the fan, for example, due to wear, noise or insufficient productivity.

In this article, we will consider a step-by-step instruction on how to replace the fan in the laptop hp. It'll save you money to go to the service center and make your laptop more effective.

Step 1: Prepare to replace the fan

Before you start replacing the fan, make sure the laptop's off and off the grid. Also remove the battery from the device to avoid electrical shock.

During the replacement, it is recommended that antistatic bracelets be used to avoid static electricity that could damage the laptop components. If you don't have an antistatic bracelet, make sure your hand touches the metal surface to cut the static electricity.

It is important to remember that the replacement of the fan may require the removal of the laptop, which may violate the guarantee of the device. Before any action is taken, consult with the producer or service centre.

Preparing for replacement of the fan

The process needs to be prepared and reviewed before the replacement of the HP fan is started. Follow these steps for the successful replacement of the fan:

1. Turn off the laptop.: Before you start replacing the fan, make sure the laptop is completely off and off the power supply.
2. Prepare the work area: It is recommended that a laptop be installed on the flat and clean surface to prevent damage or loss of parts. Use an antistatic rug or be in a low-static electric location.
3. Take off the back cover.: Look at the back of the laptop and find a cover protecting the mother's fee. With a screwdriver or other suitable instrument, clean up the lid carefully, opening access to the fan and other components.
4. Disconnect the wire.: Look at the wires that connect the fan to the mother's fee. Untie them, pull them off carefully. Remind the sequence of wires to correctly connect the new fan.
5. Open the fan.: Using a screwdriver or a special instrument, retrieve the fan carefully from the radiator or other fastening system. Be careful not to damage the delicate parts of the process.
6. Set up a new fan.: Introduce a new ventilator to its seat and carefully secure it by means of anchorages or locks. Make sure the fan is securely fixed and not moving.
7. Connect the wires.: Connect the wires of the new fan to the relevant nests on the maternal fee. Note the correct alignment and orientation of wires.
8. Set the back cover: Take the back lid and put it in a safe place, securely fixing it. Make sure all the openings and drawers match and get up correctly.
9. Check the job.: After the fan's replacement, connect the laptop to the power source and turn it on. Make sure the new fan works correctly and removes the excess heat from the laptop.

Remember that the replacement of the fan in the laptop may vary according to the model and the manufacturer. Always follow the instructions given by the manufacturer of your laptop and contact the specialists if you have difficulties or questions.

Turn off the laptop from electricity.

Before we start replacing the fan in the laptop, it's necessary. disconnect it from electricity.} It's important to your safety and to prevent damage to the components.

Follow these steps:

1. Close all the applications and keep all the important data.
2. Turn off the laptop, press the power button and hold it for a few seconds until it's completely off.
3. Disconnect the charger from the dispenser and remove it from the laptop.
4. Check carefully that the laptop is completely off the grid, pressing the power button several times.

After these steps, you can go to the replacement of the fan in the HP laptop.

Put your laptop on the working surface.

Before we start replacing the ventilator in the HP laptop, it is important to put it on a flat and sustainable surface. Note that the laptop shall be switched off and off from the power source.

The malfunctioning position of the laptop may result in damage to its body or components. Put it on a table or a desk with a soft layout to avoid a scratch on its surface.

Clearing the laptop

Before replacing the fan in the HP laptop, the device shall be removed. In this section, we will consider the main steps to clear the laptop.

Step 1: Preparation

It is important to ensure a clean and simple working place before the laptop is cleared. It is recommended that an antistatic rug or an antistatic bracelet be used to prevent static electricity that could damage the laptop components.

Step 2: Nutritional disconnect

Before you start the laptop, make sure it's off and off the grid. The battery must also be removed from the laptop.

Step 3: Covering

After the power cuts, the laptop shall be removed. Usually, the roof is secured by several screws located on the perimeter of the roof. Take these rifles off to remove the lid.

Step 4: Access to the fan

Once the roof is removed, you can access the fan. The fan may be secured by several screws or clips. Open the rifles or disconnect the clamps to release the fan.

Step 5: Replacement of the fan

Once the old fan is removed, a new vent shall be installed. Make sure the new fan matches your HP laptop model. Set up a new fan and secure it with rifles or clips.

Step 6: Collection of laptop

Once the fan is replaced, we need to reverse the process and collect the laptop. Fill the cover and secure it with the rifles. Make sure all the rifles are tightly locked and the roof is secure.

Now you know the main steps to clear the HP laptop to replace the fan. When the laptop is cleaned, always be careful and careful to avoid damage to the components. In the event of difficulties or uncertainty, it is better to turn to professionals or the HP service centre.

Open the laptop cover.

Before replacing the fan in the HP laptop, the cover shall be opened. To this end, do the following:

1. Before you start your work, you have to turn off the laptop and disconnect it from the network.
2. Put the laptop on a flat and stable surface to avoid damage.
3. Locate the rifles that hold the laptop. Usually they're on the back and have a badge similar to the fan image.
4. Using a screwdriver or a pinzet, tidy the screws and leave them in a safe place to keep them safe.
5. When all the rifles are turned off, clean the cover of the laptop, using a plastic scapula or such a device.
6. Make sure you don't hide the other parts of the laptop.

Pay attention to: The opening of the laptop can result in the loss of the guarantee if it is still in the guarantee period. If you are not certain of your skills, it is recommended that you seek assistance from a HP specialist or service centre.

Disconnect the cables

• Before you start work, make sure the laptop's off and the battery's completely out.
• Look at the back of the laptop and find where the fan is.
• Open the vent lid with a screwdriver or other suitable instrument.
• Now look carefully at the fan and his cables.
• Find the cables that connect the fan to the mother's fee.
• Carefully disconnect these cables, squeezing metal clips on the conctors and pulling cable upwards.
• Mark the cables or their compounds to know the right direction at the subsequent assembly.

Access to the fan

Before the replacement of the fan in the HP laptop, access to the component should be ensured. To accomplish this task, follow instructions:

1. First, turn off the laptop from the power source and close its cover.
2. See if there are any special badges or symbols on the laptop indicating where the fan is located. Usually, this is a badge in the form of a vent or deepening.
3. The next step will be to remove the lid that covers the ventilation laptop system. In most HP laptops, it is necessary to remove several rifles or to press the button so that the roof is off.
4. Once the roof is removed, you'll see the fan that's on the radiator. The fan may be fixed in different ways: rifles, fixed clips or locks. Consider carefully the way your fan is secured.
5. To remove the fan, turn the screws off or clean the clips or locks. Be careful and do it carefully so as not to hurt the fan or other components.
6. Once the old fan is removed, set up a new fan and secure it in accordance with instructions or in the image on the laptop.
7. Check if the fan is correctly installed and put the cover back to your place. Pull the rifles or press them so they can be safe.
8. Now you can turn on the laptop and make sure the new fan works correctly. If you have not noticed any cooling and noise problems, the task of replacing the fan has been successful.

Open the anchorages

Step 1: Turn off the laptop from the power source and close its cover. Make sure the laptop is completely off.

Step 2: Put the laptop on the clean and flat surface, like on the table or table. Put it in such a way that the fan is top and visible.

Step 3: Find the stacking of the fan on the laptop. They are usually small rifles or skirts that attach the fan to the system fee.

Step 4: With a screwdriver or a pizza, weaken the fan anchorages. Be careful not to damage system fees or other laptop components.

Step 5: After all the anchorages are weakened, clean the fan out of the system fee. Get him out of the laptop completely.

Step 6: Check the fan for damage or wear. If the fan is damaged, replace it with a new one.

Carefully extract the old fan.

An old fan must be carefully extracted before the replacement of the HP fan is started. To this end, follow the instructions below:

1. Turn off the laptop and disconnect it from the network.} It's important to your safety and to prevent damage to the equipment.
2. Turn the laptop and take his back cover off.} Usually, the rear lid is fixed by the stuns that need to be removed by a screwdriver.
3. Find the fan.} Normally, it is located near the processor and has wires connected to the maternity fee.
4. Disconnect the vent wire} To that end, get them out of the dime on your mother's fee. Pay attention to how they were connected so that a new fan could be properly connected.
5. Secure the fan anchorage.} The fan is usually fixed with a few stitches or a clip. Turn off the fuss or disconnect the clips to disconnect the fan from the cooling system.
6. Carefully extract the old fan.} When extracting an old fan, draw attention to its position and direction. Try not to damage other components and not to dust or dirt.

Now that the old fan is successfully recovered, you can start setting up a new fan in the HP laptop. Please contact the next section of the instruction for further guidance.

Question-record

What is the average life of the fan in the laptop hp?

The average life of the fan in the laptop hp is approximately 3-5 years. However, this may vary depending on the use of the laptop and its operating conditions. If the fan starts to show signs of malfunction, such as elevated noise, low cooling productivity or periodic failures, it is recommended to replace it.

What tools are needed to replace the fan in the hp laptop?

To replace the fan in the laptop hp, you'll need the following tools: a screwdriver, a pizza, armopath, a new laptop fan. The screwdriver is needed to remove the laptop cover and to secure the fan. The pink is used for more accurate work when a new fan is installed. Thermopath is necessary to ensure the right heat discharge between the processor and the fan. A new fan can be purchased from an official service centre hp or specialized stores.