How to correctly set Gammaxx 300: detailed instruction

One of the most important components in computing is the processor cooling system. If the processor is overheated, it may lead to a reduction in productivity or even a failure. One of the popular refrigeration systems is Gammaxx 300. In this article, we will tell us how to correctly set Gammaxx 300 to ensure optimal cooling of your processor.

Before you start the Gammax 300, you'll have to shut the computer off the power supply and remove the power plug. It is also important to prepare the necessary tools: screws, thermopaste, napkins and antistatic belt (if any). Remember, when dealing with computer components, care must be taken and manufacturer ' s instructions should be followed.

Before Gammaxx 300 is installed, old cooling shall be removed from the processor. To that end, clean up the fastening rifles and take off the old culer carefully. Turn it around with alcohol and napkins, remove the old thermopath from the processor surface. Note that the surface of the processor shall be perfectly clean before the installation of a new refrigeration.

The replacement of processor cooling is a responsible and sensitive matter. Be careful and follow manufacturer ' s instructions.

Now that the processor and its surface are clean, it is possible to move to Gammaxx 300. Take the plastic rubber plugs that go on the doll kit and put them on the holes on the bottom of the pay. Then wedge a thin layer of new thermopass to the surface of the processor. It will help improve the heat transfer from the processor to the dealer.

Gammaxx 300: main steps

Gammax 300 is a relatively simple process that can be performed even by a newcomer without special skills. The following are the main steps that will help you set up the Gammaxx 300:

1. Prepare all necessary tools and components for Gammaxx 300.
2. Prepare the computer system and hull, open the side wall panels and remove the previous kernel (if any).
3. Unpack Gammax 300 and make sure you have all the necessary components: the culer, the rear anchorage, the mounting racks, the fan and thermopath.
4. Set the rear anchorage of Gammaxx 300 on the back panel of your computer, flattening the holes with the panel openings, and installing the mounting racks in the deepening of the anchorage.
5. Get the fan cable through the deepening of the anchorage and connect it to the corresponding disembarkation on the maternal fee.
6. Put a small number of thermopaths on the central part of the processor.
7. Set a Gammaxx 300 to the processor, flattening the openings to the rear anchor.
8. Lower the anchorage of the pistol and tighten it with the mounting rigs, tightly delay them to secure the locking.
9. Make sure that Gammaxx 300 is tightly attached to the processor and that all the anchorages are tightly prolonged.
10. Close the computer's side panel and connect the feed to the system.

After completing these basic steps, your Gammaxx 300 should be successfully installed on your computer. Make sure that the fan works correctly and that the temperature of your processor is within normal limits. In case of problems or questions arise, contact the user ' s guide Gammaxx 300 or seek assistance from specialists.

Preparation for installation

Preparatory steps must be taken before the installation of Gammaxx 300. This will help to guarantee the successful installation and proper operation of the cooling system.

• Turn off the power of the computer: Before the work begins, the computer should be switched off and connected to the electrical network. This will prevent electrical shocks and damage to components.
• Prepare the necessary tools: For the successful installation of the Gammaxx 300 refrigeration system, the following tools will be needed: screwdriver, thermopath, surface-cleaning napkin.
• Check the compatibility: Make sure the Gammax 300 cooling system is compatible with your processor and your maternity fee. Meet the Gammaxx 300 and check that your components support this cooling system.
• Prepare the work place: Choose a suitable location for Gammaxx 300. Make sure you have enough space and all the necessary tools under your hand.
• Clear the surface of the processor and the radiator: With napkins and special equipment, remove the remnants of the old thermopath from the surface of the processor and the radiator. This will help to ensure better heat transfer and efficiency of the cooling system.

Once all the above steps have been taken, you will be ready to install Gammax 300 and move to the next phases of the installation process.

Installation of processor

All necessary tools and materials must be prepared to begin the installation of the fist on the processor: the Gammaxx 300, thermopaste, the screws, the fixtures, and the pinkette (for thermopaths).

Steps of installation:

1. Turn off the computer and get him off the grid.
2. Open the computer hull and remove the existing culler if it is installed.
3. Clear the surface of the processor from the residues of old thermopaths and contamination with isopropyl alcohol and cotton tampon.
4. Put a small number of thermopaths on the central part of the processor. Equally distribute thermopaste all over the surface with a pinkette.
5. Set a Gammaxx 300 to the processor so that the bays on its basis can be in the openings on the processor's fee.
6. Put the dealer on the processor's fee with the fastening bolts attached to it. Pull the bolts evenly so that the culler is fixed tightly and without locking.
7. Put the clerk on the mamma's dress, connecting him to the dial.
8. Close the computer and connect it to the network.
9. Turn on the computer and check the fist. Make sure he spins and creates sufficient air flow.

Once the fist is installed, its work must be stable and effective. If necessary, programs may be used to control the temperature of the processor and the speed of the fistula.

Connection to food

Gammaxx 300 is connected to your computer feeding system to ensure proper cooling of the processor. In this section, we will consider how to properly connect the dealer to feed.

1. Find the CPU nest on your mother's fee. Usually, this is a 4- or 8-contact nest marked by the " CPU FAN " or " CPU PWR " . Every time you connect or disconnect the cables from the PC, make sure it's off.

2. Open the package Gammax 300 and extract the fan and all the necessary fixtures.

3. Raise the latches on each side of the fist to open up its fastening mechanism. Set the base of the fist on the surface of your processor, making sure it is perfect for the size of the processor.

4. Put the latch down to secure the dealer on the processor. But you'll hear the cheek, which means the correct fixation.

5. Closely connect the 4- or 8-contact diet to the CPU nest on the maternal fee. Make sure the diving and nest match each other.

6. Some fists may have additional diluents, e.g., scattered for lighting. If your dealer has extra units, put them in the appropriate nest on your mother's fee.

7. See if all the connections of the fistula with the food were correct. Make sure the dips are tightly attached to the nest and securely fixed.

8. Start the computer and check the fist. Make sure the fan rots and the processor cools properly.

Now that your processor Gammaxx 300 is properly connected to feeding, he's ready to ensure optimal cooling of your processor. Make sure you correctly installed the rest of the cooling system to achieve maximum efficiency.

Question-record

What are the dimensions of the Gammaxx 300?

Dimensions of Gammaxx 300: 123 mm x 85 mm x 154 mm.

What is thermopath better to use with Gammaxx 300?

For Gammaxx 300, it is recommended to use a good thermal range based on silicone or metal-keramic thermopath. It's best to use the thermopaste that's delivered with the culer.

What are the noise parameters from the Gammaxx 300?

The sound level of Gammax 300 is 17-35 dBA (A-weighted decibel), which is very quiet for the fan of this class. This allows for low noise even with high loads on the processor.